Uncategorized

Windows 7 – AMD Radeon HD 6900 does not detect second monitor

If you are using VGA cables with a DVI-VGA adapter on the card that would be why the second monitor won’t work as only one of the DVI ports on the card is configured to work with a DVI-VGA adapter.


You need a DVI cable, as long as one of the monitors has a DVI port on it. Unfortunately not enough card manufacturers (like most of them) mention it anywhere or at least mark the backplates on the cards like this,

AMD Radeon HD 6900 does not detect second monitor-backplate.png

to indicate that the card only supports VGA via adapter from one of the DVI ports; one port being DVI-I (analogue and digital), with the other being DVI-D (digital only).

WTF homegroup

… i dont even

http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/a2cdb8cd-0453-459d-8365-9ec78a037f4c

This just happened to me, and I was tearing my hair out – until I found that windows wasn’t updating either.  The problem – my system was too far out of time with normal time

Check your system clock, make sure it is real time and date.

When I changed it, suddenly I could join the homegroup.

Post: #1Tutorial: How to setup a TF2 server
NOTE: Work in progress! Not complete!

This is based on my experience with setting up a server from scratch, IE I didnt know anything about it when I started!

Installation
1) Download the HLDSTOOLUPDATE to a temp location, like c:Temp.
Use the link below to download HLDSTOOLUPDATE.
http://www.steampowered.com/download/hldsupdatetool.exe
The tool is used to download, update and run the dedicated Source server.

2) Once you have downloaded hldsupdatetool.exe, run the installer and install to a permanent location, like c:HLServer

3) Now you need to download the files for your dedicated TF2 server.
To download the dedicated TF2 server, use this script in a .bat file:
Quote:
c:HLServerhldsupdatetool -command update -game tf -dir c:HLServer
This is how it should look, if your server location is “c:HLServer”
When downloading, dont panic over the size….its about 1,8Gb.
Sometimes the update tool will exit for no reason. Just run it again untill you are confident you have everything.

Configuration
4) Now you have you base installation. You just need to configure it.
Open Notepad and create a file called server.cfg and put it in the C:HLServerorangeboxtfcfg folder. (Remember NOT to save it as an “txt” file)
Heres a base server.cfg file:
Quote:
// Team Fortress 2 Server Configuration File, To be used with TF2 only!

// Server Name
hostname “Team Fortress 2”

// Rcon Cvars
rcon_password “” //Set’s remote control password
sv_rcon_banpenalty 15 //Number of minutes to ban users who fail rcon authentication
sv_rcon_log 1 //Enable/disable rcon logging.
sv_rcon_maxfailures 3 //Max number of times a user can fail rcon authentication before being banned
sv_rcon_minfailures 5 //Number of times a user can fail rcon authentication in sv_rcon_minfailuretime before being banned
sv_rcon_minfailuretime 10 //Number of seconds to track failed rcon authentications

// Server Password
sv_password “” // Password protects server

// Server Cvars
mp_allowspectators 1 //Toggles whether the server allows spectator mode or not
mp_autocrosshair 0
mp_autoteambalance 1 //Toggles server autoteambalance
mp_bonusroundtime 5 //Time in seconds after round win until round restarts
mp_chattime 5 //amount of time in seconds players can chat after the game is over

mp_decals 1
mp_defaultteam 1
mp_disable_autokick 1 //Prevents a userid from being auto-kicked
mp_enableroundwaittime 1 //Enable timers to wait between rounds.
mp_fadetoblack 0 //fade a player’s screen to black when he dies
mp_falldamage 5 //Amount of damage players sustains from a fall
mp_flashlight 0 //Toggles flashlight on or off
mp_footsteps 1 //Toggles footsteps on or off
mp_forcecamera 0 //Restricts spectator modes for dead players
mp_forcerespawn 0
mp_forcerespawnplayers 1 //Force all players to respawn.
mp_forcewin 1 //Forces team to win
mp_fraglimit 0
mp_idledealmethod 2 //Deals with Idle Players. 1 = Sends them into Spectator mode then kicks them if they’re still idle, 2 = Kicks them out of the game
mp_idlemaxtime 1 //Maximum time a player is allowed to be idle (in minutes)
mp_maxrounds 10 //max number of rounds to play before server changes maps
mp_teams_unbalance_limit 2 //Teams are unbalanced when one team has this many more players than the other team. (0 disables check)
mp_teststalemate 0 //Test the stalemate mode. Parameter: <0/1>. If 1, the map will reset at the end.
mp_time_between_capscoring 5 //Delay between scoring of owned capture points.
mp_timelimit 20 //game time per map in minutes
mp_winlimit 10 //Max number of rounds one team can win before server changes maps
sv_allow_color_correction 1 //Allow or disallow clients to use color correction on this server.
sv_allow_wait_command 0 //Allow or disallow the wait command on clients connected to this server.
sv_allowdownload 1 //Allow clients to download files
sv_allowupload 1 //Allow clients to upload customizations files
sv_alltalk 0 //Players can hear all other players, no team restrictions
sv_alternateticks 0 //If set, server only simulates entities on even numbered ticks.
sv_autosave 0 //Set to 1 to autosave game on level transition. Does not affect autosave triggers.
sv_bonus_challenge 0 //Set to values other than 0 to select a bonus map challenge type.
sv_cacheencodedents 1 //If set to 1, does an optimization to prevent extra SendTable_Encode calls.
sv_cheats 0 //Allow cheats on server
sv_clearhinthistory 0 //Clear memory of server side hints displayed to the player.
sv_consistency 1 //Whether the server enforces file consistency for critical files
sv_contact “” //Contact email for server sysop
sv_downloadurl “” //Location from which clients can download missing files
sv_enableoldqueries 1 //Enable support for old style (HL1) server queries
sv_pausable 0 //Is the server pausable.

// Lan or internet play, Server region cvars
sv_lan 0 //Server is a lan server ( no heartbeat, no authentication, no non-class C addresses )
sv_region 255 // Region Codes: 0 – US East coast, 1 – US West coast, 2 – South America, 2 – South America, 3 – Europe, 4 – Asia, 5 – Australia, 6 – Middle East, 7 – Africa, 255 – world

//server Logging
sv_log_onefile 0 //Log server information to only one file.
sv_logbans 1 //Log server bans in the server logs.
sv_logblocks 0 //If true when log when a query is blocked (can cause very large log files)
sv_logecho 0 //Echo log information to the console.
sv_logfile 1 //Log server information in the log file.
sv_logflush 0 //Flush the log file to disk on each write (slow).
sv_logsdir “logs” //Folder in the game directory where server logs will be stored.

//Server Rates
sv_maxcmdrate 0 //(If sv_mincmdrate is > 0), this sets the maximum value for cl_cmdrate.
sv_maxrate 20000 //Max bandwidth rate allowed on server, 0 == unlimited
sv_maxreplay 2 //Maximum replay time in seconds
sv_maxupdaterate 100 //Maximum updates per second that the server will allow
sv_mincmdrate 0 //This sets the minimum value for cl_cmdrate. 0 == unlimited.
sv_minrate 0 //Min bandwidth rate allowed on server, 0 == unlimited
sv_minupdaterate 30 //Minimum updates per second that the server will allow

Complete list of server commands:
http://www.dodbits.com/downloads/cvars/TF2/Team_Fortress_2_cvar_list_a-z.htm
Other great list:
http://forums.steampowered.com/forums/showthread.php?t=598508

Starting
To start the TF2 dedicated server you can use this command:
Quote:
c:HLserverorangeboxsrcds.exe -console -game tf -hostport 27015 +maxplayers 24 +map ctf_2fort
I start the server with the above, my server will support a maximum of 24 players, you can make it more or less if you like, and start on ctf_2fort map.

You can use the command in a .bat file

Extras
If you want to control the number of players on each class or spawntimes, use this program:
http://www.beetlesmod.com/comm/

For more info on Dedicated Server:
http://planethalflife.gamespy.com/View.php?view=HL2Guides.Detail&id=4&game=3

Fast respawn without mods, by GTFO Gaming:
http://www.gtfogaming.co.uk/forum/viewtopic.php?t=2637

How to install OpenVPN on a Debian/Ubuntu VPS instantly

This is a follow up post to How to setup a VPN server on a CentOS VPS instantly same requirements and instructions apply.
Minor distribution specific changes were made on the previous CentOS script to get it working under Debian and Ubuntu. We might create one single script which will install OpenVPN on most distributions and architectures in future.
To install issue the following commands logged in as root on your VPS (Refer to this post if you are facing any issues)
wget http://vpsnoc.com/scripts/debian-openvpn.sh
chmod +x debian-openvpn.sh
./debian-openvpn.sh
For any other issues and feedback please e-mail us at [email protected]
You may use and modify this script however you see fit, provided that you do not edit the original copyright.
#!/bin/bash
# Quick and dirty OpenVPN install script
# Tested on debian 5.0 32bit, openvz minimal debian OS template
# and Ubuntu 9.04 32 bit minimal, should work on 64bit images as well
# Please submit feedback and questions at [email protected]
# John Malkowski vpsnoc.com 01/18/2010
ip=`grep address /etc/network/interfaces | grep -v 127.0.0.1  | awk '{print $2}'`
apt-get update
apt-get install openvpn libssl-dev  openssl
cd /etc/openvpn/
cp -R /usr/share/doc/openvpn/examples/easy-rsa/ /etc/openvpn/
cd /etc/openvpn/easy-rsa/2.0/
chmod +rwx *
. ./vars
./clean-all
source ./vars
echo -e "nnnnnnn" | ./build-ca
clear
echo "####################################"
echo "Feel free to accept default values"
echo "Wouldn't recommend setting a password here"
echo "Then you'd have to type in the password each time openVPN starts/restarts"
echo "####################################"
./build-key-server server
./build-dh
cp keys/{ca.crt,ca.key,server.crt,server.key,dh1024.pem} /etc/openvpn/

clear
echo "####################################"
echo "Feel free to accept default values"
echo "This is your client key, you may set a password here but it's not required"
echo "####################################"
./build-key client1
cd keys/
client="
client
remote $ip 1194
dev tun
comp-lzo
ca ca.crt
cert client1.crt
key client1.key
route-delay 2
route-method exe
redirect-gateway def1
dhcp-option DNS 10.8.0.1
verb 3"
echo "$client" > $HOSTNAME.ovpn
tar czf keys.tgz ca.crt ca.key client1.crt client1.csr client1.key $HOSTNAME.ovpn
mv keys.tgz /root

opvpn='
dev tun
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
ca ca.crt
cert server.crt
key server.key
dh dh1024.pem
push "route 10.8.0.0 255.255.255.0"
push "redirect-gateway"
comp-lzo
keepalive 10 60
ping-timer-rem
persist-tun
persist-key
group daemon
daemon'
echo "$opvpn" > /etc/openvpn/openvpn.conf
echo 1 > /proc/sys/net/ipv4/ip_forward
iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j MASQUERADE
iptables-save > /etc/iptables.conf
echo "#!/bin/sh" > /etc/network/if-up.d/iptables
echo "iptables-restore < /etc/iptables.conf" >> /etc/network/if-up.d/iptables
chmod +x /etc/network/if-up.d/iptables
echo "net.ipv4.ip_forward=1" >> /etc/sysctl.conf
/etc/init.d/openvpn start
clear
echo "OpenVPN has been installed
Download /root/keys.tgz using winscp or other sftp/scp client such as filezilla
Create a directory named vpn at C:Program FilesOpenVPNconfig and untar the content of keys.tgz there
Start openvpn-gui, right click the tray icon go to vpn and click connect
For support/bug reports email us at [email protected]"

How to Install rTorrent/ruTorrent on Debian/Ubuntu VPS

This tutorial will guide you through the setup of a fully-featured seedbox running on a Debian or Ubuntu system, including:

  • libtorrent 0.13.0
  • rTorrent 0.9
  • ruTorrent Web UI (3.0)

This guide has been tested with Debian 6 (x86_64) and Ubuntu 11.04 (x86_64).

To start, access your VPS via SSH (as the root user) and do the following to update your platform and install some required dependencies:

# apt-get update
# apt-get install subversion build-essential automake libtool libcppunit-dev libcurl3-dev libsigc++-2.0-dev unzip unrar-free curl libncurses-dev
# apt-get install apache2 php5 php5-cli php5-curl

Enable scgi for Apache:

# apt-get install libapache2-mod-scgi
# ln -s /etc/apache2/mods-available/scgi.load /etc/apache2/mods-enabled/scgi.load

Install XMLRPC:

# mkdir /install;cd /install
# svn checkout http://xmlrpc-c.svn.sourceforge.net/…mlrpc-c/stable xmlrpc-c
# cd xmlrpc-c
# ./configure –disable-cplusplus
# make
# make install

Intall libtorrent:

# cd /install
# wget http://vps6.net/src/libtorrent-0.13.0.tar.gz
# tar xvf libtorrent-0.13.0.tar.gz
# cd libtorrent-0.13.0
# ./autogen.sh
# ./configure
# make
# make install

Install rTorrent:

# cd /install
# wget http://vps6.net/src/rtorrent-0.9.0.tar.gz
# cd rtorrent-0.9.0
# ./autogen.sh
# ./configure –with-xmlrpc-c
# make
# make install
# ldconfig

Create required directories:

# mkdir /home/seeder1/rtorrent
# mkdir /home/seeder1/rtorrent/.session
# mkdir /home/seeder1/rtorrent/watch
# mkdir /home/seeder1/rtorrent/download

Setup .rtorrent.rc file (rTorrent config):

# cd ~/
# wget http://vps6.net/src/.rtorrent.rc
# cp .rtorrent.rc /home/seeder1/

(Edit the settings in .rtorrent.rc, like max upload/download speed, max connected peers, etc, as needed.)

Install rTorrent:

# cd /install
# wget http://vps6.net/src/rutorrent-3.0.tar.gz
# tar xvf rutorrent-3.0.tar.gz
# mv rutorrent /var/www
# wget http://vps6.net/src/plugins-3.0.tar.gz
# tar xvf plugins-3.0.tar.gz
# mv plugins /var/www/rutorrent
# rm -rf /var/www/rutorrent/plugins/darkpal
# chown -R www-data:www-data /var/www/rutorrent

Secure /rutorrent:

# a2enmod ssl
# a2enmod auth_digest
# a2enmod scgi
# openssl req [email protected] -new -x509 -days 365 -nodes -out /etc/apache2/apache.pem -keyout /etc/apache2/apache.pem
# chmod 600 /etc/apache2/apache.pem
# htdigest -c /etc/apache2/passwords seedbox seeder1

(Enter a password of your choice when prompted, you will use this to log in to the ruTorrent web UI.)

# cd /etc/apache2/sites-available/
# rm -rf default
# wget http://vps6.net/src/default
# a2ensite default-ssl
# /etc/init.d/apache2 reload

Install screen:

# apt-get install screen

Start rTorrent in a detached shell using screen:

# screen -fa -d -m rtorrent

(To start rtorrent automatically when the VPS is booted, add the above command to /etc/rc.local)

You can now access ruTorrent at http://xx.xx.xx.xx/rutorrent/(replace xx.xx with your server’s IP address). You should be greeted with a login prompt, where the username is “seeder1” and the password is the one you set above in the “secure /rutorrent” section.

Easy ruTorrent installer + Web server, FTP, Webmin (Ubuntu/Debian/Fedora/More)

All credit goes to Author brock from forums.rutorrent.org  original post here for reference also check there for faq questions regarding his script

This is an easy installer for ruTorrent (multi-user support), rtorrent, plugins and other dependencies. It requires noLinux knowledge. The only requirement is that you can copy and paste three lines of code. In 5-10 mins, you should have a fully working ruTorrent.

To install it, use one of the three lines of code below, depending on which OS you are using. The installation script will ask you some questions and then install everything you selected.

Ubuntu and Ubuntu clones:
cd
wget –no-check-certificate -O autodl-setup http://sourceforge.net/projects/autodl-irssi/files/autodl-setup/download
sudo sh autodl-setup

Any other OS
Log in as root:
yum update
allow it to update all
su –
Then install it:  to install wget on centos use “yum install wget”
wget –no-check-certificate -O autodl-setup http://sourceforge.net/projects/autodl-irssi/files/autodl-setup/download
sh autodl-setup

If you already have another web server installed, you may need to disable it or uninstall it. If you don’t, the web server this script installs (*) might not work.

What it will do:

  • Install a web server (*)
  • Install ruTorrent with multi-user support (http and https)
  • Install 1st party ruTorrent plugins
  • Install an encrypted FTP server (vsftpd)
  • Install rtorrent with xmlrpc-c support
  • Install the IRC auto downloader plugin (autodl-irssi)
  • Install Webmin
  • Install a startup script for rtorrent and Irssi

You can disable any of the above by answering no when you run the installer.

* Apache, nginx, or lighttpd.

I’ve tested the following OSes (clean installs):

  • Arch Linux 2010.05
  • ArchBang 2010.10
  • CentOS 4.8
  • CentOS 5.5
  • ClearOS 5.2
  • Debian 4.0r7
  • Debian 5.0.3
  • Debian 5.0.7
  • Debian 6.0.0
  • Fedora 13
  • Fedora 14
  • Fedora 15
  • Frugalware 1.3
  • Gentoo 1.12.14
  • Linux Mint 8
  • Linux Mint 9
  • Linux Mint 10
  • Mandriva Linux release 2008.0
  • Mandriva Linux release 2010.1
  • MEPIS 8.5
  • openSUSE 11.1
  • openSUSE 11.3
  • openSUSE 11.4
  • Pardus 2009.2
  • Pardus 2011
  • PCLinuxOS 2010
  • Peppermint OS
  • RHEL 5.5
  • RHEL 6.0
  • Sabayon 5
  • Scientific Linux 5.5
  • Scientific Linux 6.0
  • Ubuntu Server 6.06.2 LTS
  • Ubuntu Server 8.04.4 LTS
  • Ubuntu Server 10.04.1 LTS
  • Ubuntu Server 11.04
  • Ubuntu 10.10
  • Unity release 2010

If your OS isn’t listed, but is derived from one of the above OSes, then the installer could still work. Eg., all Ubuntu and Debian derived OSes should work.

Issues:
SELinux:

  • If you have SELinux enabled, it’s possible Apache or vsftpd won’t work.
  • To disable Selinux.
  • Edit /etc/selinux/config (e.g. $sudo vi /etc/selinux/config)

    Find the line:

    SELINUX=enforcing

    If you simply want to set selinux to permissive mode – which will still warn you when something would have been denied

    change to

    SELINUX=disabled

Firewall:

  • The script doesn’t open any ports in your firewall. If your firewall is enabled, you may need to open a few ports.
  • if u cant access webgui use “iptables -F”

Ubuntu Server 6:

  • You need to enable the universe repository

RHEL/CentOS/Scientific 4 & 5:

geoip plugin:

  • Some OSes don’t have the PHP geoip module (thus disabling the ruTorrent geoip plugin).

Administer Ubuntu Server 12.04 using VNC

Once you’ve installed Ubuntu Server you will need a mechanism to be able to administer it. One way is to Install Putty. Putty gives you a “Command Line” interface and so you’ll need to learn a few Linux commands in order to be able to administer your server this way. Some people find this prospect rather too daunting and would rather use a graphical user interface (GUI) instead. As a result many people actually install Ubuntu Desktop instead of installing Ubuntu Server since the desktop version of Ubuntu has the GUI built in. There is a better way however, and that is to install VNC. VNC provides a “virtual desktop” so it is more lightweight than a full blown desktop installation.

NOTE: If you’re jumping into this guide here then it’s worth mentioning that this guide has been tested on Precise Pangolin 12.04LTS, Lucid Lynx 10.04LTS, Karmic Koala 9.10, 9.04 Jaunty, and 8.10 Intrepid. However, at the time of writing VNC is quite flaky on Precise Pangolin 12.04LTS (although it is getting better all the time) and so I don’t particularly recommend you attempt to install it on this version of Ubuntu. You might want to head over to the forums for the latest views on VNC on 12.04.
So to perform the installation of VNC you can either type the following commands from a Putty session or, if you’ve got a screen and keyboard attached to your server, then you can use the command line itself.
First off you need to type:
sudo apt-get update
You’ll be prompted for a password. This is the password you created when you installed Ubuntu. Ubuntu tends to prompt for a password each time you issue a “sudo” command.
TIP: If you’re going to be following this guide step by step using Putty then you can save yourself some typing by simply highlighting each command below, right-clicking on it and selecting Copy. Then toggle over to your Putty Session and right-click once more. The command you’ve just copied from here will be automatically pasted into your Putty Session.

Install the Gnome components

First off we need to install the Gnome components for our virtual desktop. So type the following command (or copy it!):
sudo apt-get install gnome-core
when prompted type Y and then press [Enter]. This will install the gnome desktop components.

Install a Virtual Desktop using VNC

Now we’ve installed the gnome components for the desktop we need to install VNC to be able to interact with it. So type:
sudo apt-get install vnc4server
when prompted type Y and press [Enter]. This will install VNC Server which is required for running the virtual desktop on the server. Next type:
vncserver
You’ll then be prompted to create and verify a new password. Once you’ve entered it you’ll see the following screen:
We now need to kill the session we just created and make a tweak to the startup script for VNCServer to make it work properly. If we don’t perform this step then all we will see is a grey cross-hatched screen with an “X” cursor and/or a grey screen with a Terminal Session, depending on the Ubuntu version. Not very useful!
You’re probably wondering why we just created a session and then killed it before we’d actually used it? Well, creating the session for the first time automatically generates the file we now need to edit.

So, type the following command to kill the session:

vncserver -kill :1
Now type the following command to open up the file we need to edit:
vim .vnc/xstartup
The modifications we need to make to this file depend on the version of Ubuntu we’re using so make sure you follow the correct section:

Ubuntu versions up to and including 9.10 Karmic Koala

Scroll down to the line which currently reads #unset SESSION_MANAGER and press the [Insert] key once (this will switch us into “edit” mode) and then remove the #
Do the same for the line after that. Plus change that line to read as follows:
exec sh /etc/X11/xinit/xinitrc
Note the “sh“.
Change the xterm -geometry line as below and once you’ve made these changes the file should look like this:
#!/bin/sh

# Uncomment the following two lines for normal desktop:
unset SESSION_MANAGER
exec sh /etc/X11/xinit/xinitrc

[ -x /etc/vnc/xstartup ] && exec /etc/vnc/xstartup
[ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources
xsetroot -solid grey
vncconfig -iconic &
xterm -geometry 1280×1024+10+10 -ls -title “$VNCDESKTOP Desktop” &
twm &

Ubuntu Versions 10.04 Lucid Lynx & Maverick Meerkat 10.10

Change the file as above but note the last two lines are different in these versions of Ubuntu:
#!/bin/sh

# Uncomment the following two lines for normal desktop:
unset SESSION_MANAGER
exec sh /etc/X11/xinit/xinitrc

[ -x /etc/vnc/xstartup ] && exec /etc/vnc/xstartup
[ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources
xsetroot -solid grey
vncconfig -iconic &
x-terminal-emulator -geometry 1280×1024+10+10 -ls -title “$VNCDESKTOP Desktop” &
x-window-manager &

Ubuntu Version Precise Pangolin 12.04LTS

Change the file so it looks like this:
#!/bin/sh

# Uncomment the following two lines for normal desktop:
unset SESSION_MANAGER
#exec /etc/X11/xinit/xinitrc
gnome-session –session=gnome-classic &

[ -x /etc/vnc/xstartup ] && exec /etc/vnc/xstartup
[ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources
xsetroot -solid grey
vncconfig -iconic &
#x-terminal-emulator -geometry 1280×1024+10+10 -ls -title “$VNCDESKTOP Desktop” &
#x-window-manager &

So, we’ve unmasked the unset SESSION_MANAGER line, added the gnome-session –session=gnome-classic & lineand masked the last two lines out.

All Versions

When you’re done editing the file for your particular version of Ubuntu press the [Esc] key once and type the following:
:wq
This should save the changes and bring you back to the command line. If you make a mistake editing the file then issue :q! instead of :wq to abort your changes.
Next type the following command to create the VNC Session once more:
vncserver -geometry 1280×1024
where 1280×1024 is the resolution of your DESKTOP COMPUTER. It has nothing to do with the resolution of the server itself. This command will create a new VNC session on your server. Note: For versions of Ubuntu prior to Precise Pangolin 12.04LTS add a -depth 24 argument so the command should read vncserver -geometry 1280×1024 -depth 24
Next, download and install TightVNC onto your desktop computer. When you launch it type the “X Desktop name” in the VNCServer box. See the DOS-type screenshot above for the name of your “X Desktop name”. So, in my case I’d typeMyMediaServer:1 in the VNC Server Listbox. See below.
then click Connect, enter the password you created when you typed the vncserver command the first time round and you should then see a screen like this (Note that on Precise Pangolin 12.04LTS the screen is blue and that error message doesn’t appear):
Click the Delete button on the error message which is displayed and you now have a nice shiny desktop view onto your server!
Incase you’re wondering how what we’ve just installed differs to simply installing the full blown Desktop version of Ubuntu then connect a screen to your server now and you’ll see it’s still sitting there on a black screen with a flashing cursor waiting for you to type your username in. What we’ve just installed is just a “virtual desktop” onto your server. Neat eh!
Currently this “virtual desktop” runs in a window on your Windows desktop. If you want to switch to “Full Screen” mode, right-click on the TightVNC icon on the taskbar on your windows desktop and select Full screen from the menu. ClickOK on the next message. Now it’s as tho you’re actually sitting in front of your server. Very cool!
To switch out of Full Screen mode and return to Window mode press Ctrl-Esc on your keyboard to bring back your Windows Desktop taskbar. Then right-click on the TightVNC icon on the taskbar and uncheck the Full Screen option.
I know a lot of people wouldn’t bother installing a virtual desktop on their servers (and I’ve no doubt any Linux veterans reading this will be scoffing that I’ve done so) but I was a total Linux newbie when I started this project and the thought of administering everything using the command line was simply too daunting a prospect. Even tho I now feel much more comfortable with Ubuntu I still find it really handy to just nip into the Ubuntu desktop and tweak something.
When you reboot the server you’ll discover that you are unable to re-launch the VNC session and you’ll receive a “Failed to connect to server” error message. This is because the vncserver -geometry 1280×1024 -depth 24 command we typed above is not persistent. To solve this we need to ensure that VNC is run on boot: How to run VNC on startup

The Synaptic Package Manager is not installed by default in Lucid or Karmic

At the time of writing the Synaptic Package Manager does not get installed by default in Lucid or Karmic when you install the core gnome desktop. The Synaptic Package Manager is a great tool which makes adding and removing applications a breeze. So we’ll simply install it manually by typing the following two commands in a Terminal/Putty session:
sudo apt-get update
sudo apt-get install synaptic
When you now go into your server desktop via VNC you’ll find the Synaptic Package Manager under the System ->Administration menu.

How to prevent Gnome starting on the server on boot

On Ubuntu versions 10.10 (Maverick Meerkat), 11.04 (Natty Narwhal), 11.10 (Oneiric Ocelot) & 12.04 LTS (Precise Pangolin) gnome is automatically started on boot once the above instructions have been followed. So, if you connect a monitor to your server you will see the GUI sitting there waiting for you to log in. You can prevent this happening by carrying out the following tweak:
So, issue the following command to open up the relevant script:
sudo vim /etc/init/gdm.conf
You want to mask out the few lines which start the service ie. start on ((filesystem…. so the first few lines of the script should look like this once you’ve edited it:
# gdm – GNOME Display Manager
#
# The display manager service manages the X servers running on the
# system, providing login and auto-login services

description “GNOME Display Manager”
author “William Jon McCann <[email protected]>”

#start on ((filesystem
# and runlevel [!06]
# and started dbus
# and (drm-device-added card0 PRIMARY_DEVICE_FOR_DISPLAY=1
# or stopped udev-fallback-graphics))
# or runlevel PREVLEVEL=S)

stop on runlevel [016]

emits login-session-start

Save your changes then reboot the server and that log-in screen should no longer appear. 

Hard Reset Or 30/30/30 on a router

Image:Warning.png
DO NOT attempt to reset or power cycle the router while it is still in the process of upgrading!
Wait a couple of minutes after upgrade is complete and the router has rebooted itself.

Hard Reset (aka 30/30/30 reset):

The following procedure will clear out the NVRAM and set dd-wrt back to default values:
  • With the unit powered on, press and hold the reset button on back of unit for 30 seconds
  • Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
  • Plug the unit back in STILL holding the reset button a final 30 seconds (please note that this step can put Asus devices into recovery mode…see note below!)
This procedure should be done BEFORE and AFTER every firmware upgrade/downgrade.
Do not use configuration restore if you change firmware builds (different svn build numbers).
[NOTE] – For Asus units, the standard 30/30/30 method will reset the router but you will need to use the Restore button followed by a Power cycle. The only exception (so far) is the RT-N16 model, follow the same method as stated above but use the WPS button instead of the Restore button. If all else fails to reset you can also do it by command line (all units). Login to the router via telnet/ssh and issue the command “erase nvram”. This will reset the nvram partition to defaults for this Make of router.….redhawk

Erasing NVRAM:

As an alternative method, it is possible to restore DD-WRT to default settings without using the reset button (useful if you’re locked out of the web interface or the reset button is disabled, broken, etc. or if your router just refuses to reset using 30/30/30).
[CAUTION] - On some devices, resetting NVRAM in this fashion may cause more problems than it solves. For example, Asus WL-500g and the Motorola WR850G bootloader will not recreate default values and will not boot properly after being reset. If you do this on a Siemens SE505 V1, your router will not be accessible to you anymore! You will have to reflash it with the stock firmware on IP address 192.168.1.1 (NOT 192.168.2.1 as the installation procedure says!!)
The following requires that DD-WRT already be installed on your router, and Telnet (or SSH) services be enabled and accessible.
Telnet (or SSH) into 192.168.1.1
Issue commands:
erase nvram
reboot
or
mtd -r erase nvram
The mtd method should be used with caution! The erase nvram;reboot method is much safer!
All should be in default settings now.


Default password

After resetting DD-WRT, you need to login with the user name “root” and password “admin”.

DD-WRT on Linksys E1000 v1 or v2

Linksys E1000

Please see this thread for information on E1000 and dd-wrt compatibility http://www.dd-wrt.com/phpBB2/viewtopic.php?t=79673


Install / Flash Linksys E1000 v1 only! (see above link for v2)

The following instructions are copied from Dark_Shadow’s forum post / wiki see: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=79673 (same as link above). I am adding them here after testing and validating they work as per his request in the forum. They worked flawlessly for me installing on a Cisco Linksys E1000 v1 [–Apus.one 05:08, 15 October 2011 (CEST)].
  1. Read the Peacock Announcement.
  2. Download dd-wrt.v24-15279_NEWD-2_K2.6_mini_e1000.bin. If you wish to experiment with a newer build, you should read the “build thread” for any build you are considering putting on your router, before flashing a newer build, (as discussed in the peacock announcement).
  3. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them.
  5. Ensure you have a physical ethernet connection to your router, and disable your wireless adapter, antivirus/firewall protection, and any software that makes strong use of your network (BitTorrent, Streaming Audio/Video, etc).
  6. Perform a hard 30/30/30 reset.
  7. Navigate to http://192.168.1.1/ in your web browser of choice.
  8. At the Linksys Administration > Firmware Upgrade page, do not give the reboot command. You will use this page to upgrade your firmware.
  9. Browse to the firmware you downloaded and click Upload.
  10. Do not touch anything. The page will tell you that the upgrade was successful and the router is now rebooting. Your router may take upwards of a couple minutes to reboot. Watch the lights… once the wireless and power indicators are on steadily for several seconds, your router is fully rebooted and you can click “Continue” in your browser window.
  11. If the DD-WRT password change page displays, your upgrade has been successful, and you must now perform another hard 30/30/30. This time, when you navigate to http://192.168.1.1/, click “Reboot” and wait for the router to come online again so you can configure it.
If the DD-WRT password change page does not display, your page request times out, or you can’t ping 192.168.1.1, make sure both wireless and power lights are on steadily first, then do a hard power cycle (unplug the power from the router–do not do a 30/30/30 reset). Wait a few seconds and plug the power back into the router. Wait until both wireless and power lights are on steadily, then navigate to http://192.168.1.1/ in your browser of choice again. If the DD-WRT password change page displays, your upgrade has been successful, and you must now perform another hard 30/30/30. This time, when you navigate to 192.168.1.1, click “Reboot” and wait for the router to come online again so you can configure it.
You can also flash the same firmware of TomatoUSB as described for WRT160N_v3.0


Performing a 30/30/30 Reset on a Linksys E1000 v1.0

  1. Perform a normal 30/30/30 reset.
  2. Login to http://192.168.1.1/ and you will see the Linksys – Management Mode page.
  3. Click “Reboot.”
  4. In a moment, you will see “Command reboot completed.” The router will now start the reboot process. When the lights return to their normal state, you can click “Continue” to be taken to the router’s main page.

Serial Recovery

I had an awfully difficult time doing serial recovery on this router. It was my first time so you can imagine that I had no idea what I was doing. There are some slight deviations from the standard serial recovery procedure that is in the Wiki so I decided it would be a good idea to add the information here. First of all, the pinout is the same as the E2000 (at least for the E1000 v2).
You should familiarize yourself with the Serial Recovery article before trying this, I’m not going to explain everything again here.
Here is the serial pinout. Image:E1000v2_serial.jpg
Looking from the back of the router you should see the 2×6 JTAG port and above that 5 holes. These 5 holes are the serial port. Again, looking from the back of the router: VCC – RX – TX – ? – Gnd
Once at the prompt you need to assign an IP/Subnet mask to eth0. I’m not sure if eth0 is the routers interface to the switch or one specific port but I had a CAT5 cable hooked up to port 1 on the router and it worked.
If you type “ifconfig eth0” you will see that there is no address assigned to the interface. The following command will assign an address/mask.
CFE> ifconfig eth0 addr=192.168.1.1 mask=255.255.255.0
Now you can flash using a TFTP client from your computer, which is plugged in to port 1 on the router, just like theSerial Recovery page says.

JTAG!

Barryware, using a mixture of perseverance and brilliance, has found a way to fix the fact that Linksys, in for completely baffling reasons, did not connect the jtag port to the processor. This isn’t for the faint of solder, but there IS now a way to jtag the 160nV3 and the E1000_V1! See this: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=146077
flash -ctheader : flash1.trx